The NCC 2022 Volumes 1 and 2 Performance Requirements F8P1 and H4P7 for Class 1, 2 and 4 state that “risks associated with water vapour and condensation must be managed to minimise their impact on the health of occupants”.

The health of building occupants can be affected if the internal surface of an external (facade and basement) wall demonstrates mould/mildew and fungus development. There are two conditions for these problems to emerge: (a) the presence of water vapour, and (b) the availability of nutrients.

Nutrients for growth are unavoidable as spores are always present in the air. They will germinate and grow (even if only at a microscopic level) if temperature and humidity conditions are suitable. Most building materials, furnishings, contents, and the unavoidably dusty environment in the car park/storage area all contain nutrients to some extent. This is beyond the control of the building designer.

Therefore, to avoid mould/mildew and fungus, water and/or water vapour must be eliminated. There are two primary sources causing this problem: (a) condensation related water, and (b) a leaking external wall.

Condensation: Various sources (and academic papers) note that a relative humidity of 60% or greater will provide a condensation water source. So, the humidity level within the interior space and/or the temperature at the internal face of an external wall must be controlled.

Leaking external wall: A leaking external wall will result in significantly more water presence than what will occur through a condensation water source, all but guaranteeing mould/mildew and fungus development.

The NCC 2022 stipulates a DTS requirement to minimise mould/mildew or fungus, or alternatively the Verification Method requires that the mould growth index must be less than 3. Both are very stringent requirements and so the best way to ensure compliance is to design such that no water or water vapour is possible.

The main problem with basement walls is water leak rather than condensation. Any water entering a habitable space in a basement would be unacceptable. Indeed, even water in non-habitable areas of the basement needs to be addressed as mould in the basement can impact the habitable areas above.

Mould

Research by the Universities of Yale and Tulsa into mould transmission in a 3-storey building with a single level basement found that up to 30% of the basement mould/mildew travelled to the 2nd floor as shown in the above diagram. The report suggests that mould transmission would be more than 30% for a property with an HVAC system.

Building designers, certifiers and local councils, therefore, should consider the following before adopting ‘water shedding design principles for below ground structures’ recently promoted by some industry players:

NCC F8P1 and H4P7 became mandatory requirements on 1st October 2023.
The guidelines for the implementation of the NSW Water Management Act 2000 , Section 1.4 note a preference for a fully tanked basement where groundwater (permanent or temporary) is impacted (Other Australian states’ building authorities have similar requirements). This also serves the purpose of newly introduced NCC requirements (NCC F8P1 and H4P7) by preventing water/water vapour ingress.
There are 5 Sydney Councils already requiring ‘fully tanked’ systems to comply with #2 above and, of course, this requirement will also deliver a basement compliant with NCC F8P1 and H4P7. For these reasons it should be expected that the number of Councils mandating tanked basements in the presence of ground water will increase. As a side benefit, specifying fully tanked basements from the start should significantly reduce DA approval time.
The ongoing operation of basement pumps during the life of the building must be included in the energy efficiency calculations for the project.
Limitations placed by Councils and Water Authorities on the discharge of pumped groundwater into their assets.

As explained above, even a small amount of water vapour or water is adequate to cause mould/mildew and fungus growth. Flood water, unmaintained and/or non-air tight pump out systems, high ground water table, seasonal water table fluctuation, undrained surface rainfall or groundwater seepage, and unmaintained/ blocked agricultural lines are some of the many reasons for the water source to cause mould/ mildew/ fungus problems in basements.

The only effective solution to prevent water entering the building interior is for the basement to be ‘fully tanked’ or, alternatively, to utilise the DINCEL solution.

Architecture & Design Team

Dincel Structural Walling

Let’s connect!